- Packet tracer activity connectivity test feature verification#
- Packet tracer activity connectivity test feature Pc#
- Packet tracer activity connectivity test feature windows#
Note: Solo players can open both files and complete the steps for both sides. – The client side player opens Packet Tracer Multiuser – Tutorial – Client Side.pka. – The server side player opens Packet Tracer Multiuser – Tutorial – Server Side.pka. Determine which of you will play the server side and which of you will play the client side in this activity. Your computers must both be connected to the same LAN.ī. Find a fellow classmate with whom you will cooperate to complete this activity. Part 1: Establish a Local Multiuser Connection to Another Instance of Packet Tracer Step 1: Select a partner and determine the role for each student.Ī. However, it can also be completed as a solo activity simply by opening the two separate files to create two separate instances of Packet Tracer on your local machine. Ideally, this activity is meant for two students. This first Packet Tracer Multiuser (PTMU) activity is a quick tutorial demonstrating the steps to establish and verify a multiuser connection to another instance of Packet Tracer within the same LAN. The multiuser feature in Packet Tracer allows multiple point-to-point connections between multiple instances of Packet Tracer. Part 2: Verify Connectivity across a Local Multiuser Connection Background Part 1: Establish a Local Multiuser Connection to another Instance of Packet Tracer Still on RouterA, run extended traceroute again but this time change the timeout value to 7 seconds.Packet Tracer Multiuser – Tutorial Addressing Table A higher number of probes allows for a more accurate average round trip time for the packets.ĭ. Note: Probe count specifies the number of ICMP packets sent to each hop by traceroute. How many ICMP packets were sent by RouterA?
How many questions were answered with non-default values? What was the new value? Simply press ENTER to use the default value. Note: the value displayed in brackets is the default value and will be used by traceroute if no value is entered. Extended traceroute should run right after the last question is answered. Answer the questions asked by extended traceroute as follows. Notice that just the traceroute command should be entered.Ĭ.
Packet tracer activity connectivity test feature windows#
Note: Windows tracert also allows the user to adjust a few aspects through the use of command line options.ī.
Packet tracer activity connectivity test feature verification#
Extended traceroute allows the administrator to adjust minor traceroute operation parameters by asking simple questions.Īs part of the verification process, use extended traceroute on RouterA to increase the number of ICMP packets traceroute sends to each hop. In addition to traceroute, Cisco IOS also includes extended traceroute. What is noticeably different about the list of addresses returned?
Packet tracer activity connectivity test feature Pc#
Compare the output from the router traceroute command with the PC tracert command.
Observe the output from the tracert command. From the PC1 Command Prompt, enter the tracert 10.1.0.2 command.ī. Step 4: Verify that end-to-end connectivity is established.Ī.
Make the necessary changes to restore connectivity however, do not change the subnets. Does there appear to be anything extraordinary?ĭ. Compare the IP addresses on the interfaces with the network addresses on the topology. What devices have addresses configured for the network where the failure occurred?ī. The furthest device from the host 10.0.0.2 with an address in the network range found is the point of failure. Compare the last address reached with the tracert command with the network addresses listed on the topology. What is the last address reached with the tracert command?Ī. Observe the results of the tracert command. What was the first IP address listed in the tracert output?Ĭ. When you receive the Request timed out message, press Ctrl+C. From the Command Prompt of PC1, enter the tracert 10.1.0.2 command.ī. Step 2: Trace the route from PC1 to determine where in the path connectivity fails.Ī. What message is displayed as a result of the ping? Step 1: Send a ping from one end of the network to the other end.Ĭlick PC1 and open the Command Prompt. After the issue is corrected, use the tracert and traceroute commands to verify the completion. You are required to examine the output of tracert (the Windows command) and traceroute (the IOS command) as packets traverse the network and determine the cause of a network issue. This activity is designed to help you troubleshoot network connectivity issues using commands to trace the route from source to destination. Part 2: Compare to the traceroute Command on a Router Part 1: Test End-to-End Connectivity with the tracert Command Packet Tracer - Testing Connectivity with Traceroute